Archive | March, 2009

Etching ceramics

As I mentioned in the previous post, I am working on a number of sabinos right now. I thought I would show some pictures of how that kind of color is done in ceramic underglaze.

White hair detail like the kind seen on sabino roans are done with a process similar to what cold painters call etching – though ceramic artists call it scritching. Until the underglazes are fired, ceramic paint is chalky and easily marred. Since the base material (the earthenware clay) is white, ceramic artists often take advantage of that fact when they need to add white markings or white hairs.

Most of the time the favored tool is a very sharp #11 Xacto blade. With my own horses I use a wide variety of blades (many sharp, but some dulled) and erasers to get just the right effect. I will sometimes use an initial layer (or layers) of white underglaze to get the right effect.

That is what I did with the guy pictured in the previous post. There is a light layer of opaque white underglaze under his gray areas. Without this, the transparent colors I have used for his body color are difficult to remove. I’ve only used a light layer, though, because I want a softer effect. In general, the thicker the layer of white the crisper the edges will be.

In the previous picture I had started adding the irregular roaning of his sabino pattern. This side, however, has not yet been detailed. This is how he looked right after his base color was sprayed and the latex masking was removed. The latex is too gloppy to mask the actual pattern, so only the whitest areas are covered. The real outline of the pattern, as well as all the hair detailing, will be done with the blades and erasers.

This picture also shows just how flat and chalky the underglazes are. Underglazes begin to look opaque long before they really are, so the body color often looks quite flat until after the horse has been through the final glaze firing. That’s why most glazers paint by memory, rather than by sight. Remembering how many times you hit an area, and how hard you hit it, is the most reliable way to predict the end coloring.

Here is the belly showing one side that has been detailed using scritching, while the other side is largely untouched. I tend to work one side at a time, which was a habit I developed long ago when I was a cold painter. I wish I had the discipline to paint one part (like the whole head, or all the legs) at a time, but I always get impatient to see one finished side.

In the other post I also mentioned “scritching claw”. It is true that making precise ticks with a tiny blade is hard on the hand, but it’s the left hand that truly suffers. I have mentioned before that unfired underglaze cannot be touched, and that even fired underglaze has to be handled very gently. One of the biggest challenges in working with underglazes is plotting your hand holds. Here with this guy I had already painted his mane, tail and feet and fired them so that I could have a three-point grip on him. (Notice that my middle finger is not actually touching his back, which has raw underglaze at the moment.)

I have to hold him like this, without rubbing those areas overly much and without exerting any sideways pressure on his legs. (Finn is pretty sturdy in that regard, but for finer legs this can be a real issue.)

That’s one reason why I tend to gravitate towards clean legged colors for my first glazed piece in a run. Tobianos, with their white legs, have four obvious hand holds. Toveros have those hand holds, and allow me to experiment with scritching without a huge time investment. All of this allows me to get aquainted with the mold a bit, learning the logical handholds and also where I am likely to run into trouble. (Will it be hard to reach between the front legs to etch the lower chest without hitting the knee with the back of the blade, for instance?)

And here is my sabino guy with one side fully scritched, sitting next to the sheet protector holding the set of reference pictures I was working from with him. I don’t usually work this closely from a specific horse, but I wanted to address a certain set of issues with this piece so I’ve been staying pretty close to the picture.

Since taking these pictures, his second side is half-finished. His firing buddy, a sabino Voltage, is not quite so far along. She has a lot more area to scritch, and a considerably larger amount of white. I’ve been taking pictures of her in-progress, too, but I want to post hers as a group once she is done. I have high hopes that at least some of these guys will be in their final, shiny form by the end of the week. Maybe by then I will have made a decision what color to paint my Vixen!

Continue Reading

One step closer

Here is the first bisque set of Vixen and Imp. I’ve learned the hard way that one bisque only tells me that it is possible to make the horse. It will take a few more before I know if the edition is feasible. But it’s one step closer, and she presented enough challenges that there were times when I wondered if I would make it this far.

I usually keep the first glazed piece from each edition, but I must admit I cannot decide her color. I looked over my “first piece” collection, and realized that they are almost all tobianos and toveros. Those types of patterns take fewer sessions (either scritching or firing) to create and they present far fewer technical problems. Usually by the time I’m holding that first bisque, I’m impatient to see color on the horse and the bisques seem too precious to do a color that might seem a little dicey. I’m on the fence whether to try something crazy and time-consuming with this first one, or avoid tempting fate.

Though perhaps with all the sabinos I have currently in the works, I think my “scritching claw” might never go away long enough to paint her!

Continue Reading